vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 1 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, phototransistor output, high reliability, 5300 v rms description the 110 c rated vo617a feature a high current transfer ratio, low coupling capacitance and high isolation voltage. these couplers have a gaas infrared diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a plastic dip-4 package. the coupling devices are design ed for signal transmission between two electrically separated circuits. the couplers are end-stackable with 2.54 mm spacing. creepage and clearance distances of > 8.0 mm are achieved with option 6. this version complies with iec 60950 (din vde 0805) for reinforced insulation up to an operation voltage of 400 v rms or dc. specifications subject to change. features ? operating temperature from -55 c to +110 c ? good ctr linearity depending on forward current ? isolation test voltage, 5300 v rms ? high collector emitter voltage, v ceo = 80 v ? low saturation voltage ? fast switching times ? low ctr degradation ? temperature stable ? low coupling capacitance ? end stackable, 0.100" (2.54 mm) spacing ? high common mode interference immunity ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications ?ac adapters ?smps ?plc ? factory automation ? game consoles agency approvals safety application model numbe r covering all products in this data sheet is vo617a. this model number should be used when consulting safety agency documents. ? ul1577, file no. e52744 ? cul tested to csa 22.2 bulletin 5a ? din en 60747-5-5 (vde 0884-5), available with option 1 ? bsi iec 60950; iec 60065 ? fimko en 60065, en 60950-1 ? cqc gb8898-2011 note ? additional options may be possib le, please contact sales office. e c a c 1 2 4 3 ordering information vo6 1 7a - #x0 # # t part number ctr bin package option tape and reel agency certified/package ctr (%) 5 ma ul, cul, bsi, fimko 50 to 600 40 to 80 63 to 125 100 to 200 160 to 320 80 to 160 130 to 260 200 to 400 dip-4 vo617a vo617a-1 vo617a-2 vo617a-3 vo617a-4 vo617a-7 vo617a-8 vo617a-9 dip-4, 400 mil, option 6 - - - vo617a- 3x006 vo617a- 4x006 --- smd-4, option 7 - - vo617a- 2x007t vo617a- 3x007t vo617a- 4x007t --- vde, ul, cul, bsi, fimko 50 to 600 40 to 80 63 to 125 100 to 200 160 to 320 80 to 160 130 to 260 200 to 400 dip-4, 400 mil, option 6 - - - vo617a- 3x016 vo617a- 4x016 vo617a- 7x016 vo617a- 8x016 - smd-4, option 7 - vo617a- 1x017t vo617a- 2x017t vo617a- 3x017t vo617a- 4x017t vo617a- 7x017t vo617a- 8x017t vo617a- 9x017t 10.16 mm option 6 7.62 mm dip-4 option 7 > 8 mm
vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 2 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the absolu te maximum ratings can ca use permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of th e time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mounted devices (smd), and wave profile for soldering conditions f or through hole devices (dip), please go to assembly instructions ( www.vishay.com/doc?80054 ). fig. 1 - total power dissipation vs. ambient temperature absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input reverse voltage v r 6v forward current i f 60 ma forward surge current t p 10 s i fsm 2.5 a led power dissipa tion at 25 c p diss 70 mw output collector emitter voltage v ceo 80 v emitter collector voltage v eco 7v collector current i c 50 ma collector peak current t p /t = 0.5, t p 10 ms i cm 100 ma ouput power dissipation at 25 c p diss 150 mw coupler isolation test voltage (rms) t = 1 min v iso 5300 v rms total power dissipation p tot 200 mw operation temperature t amb -55 to +110 c storage temperature range t stg -55 to +150 c soldering temperature (1) 2 mm from case, 10 s t sld 260 c 0 50 100 150 200 250 0 20 40 60 80 100 120 p tot - total power di ss ipation (mw) t amb - ambient temperature ( c) coupled device detector led
vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 3 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? minimum and maximum values are testing requirements. typical values are characteristics of the device and are the result of en gineering evaluation. typical values are for information only and are not part of the testing requirements. electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input forward voltage i f = 60 ma v f 1 1.35 1.65 v reverse current v r = 6 v i r 0.01 10 a junction capacitance v r = 0 v, f = 1 mhz c j 13 pf output collector emitter leakage current v ce = 10 v vo617a-1 i ceo 250 na vo617a-2 2 50 vo617a-3 5 100 vo617a-4 5 100 vo617a-7 5 100 vo617a-8 5 100 collector emitte r capacitance v ce = 5 v, f = 1 mhz c ce 5.2 pf collector emitter breakdown voltage i c = 1 ma bv ceo 80 v emitter collector breakdown voltage i e = 100 a bv eco 7v coupler collector emitter sa turation voltage i f = 5 ma, i c = 1.0 ma v cesat 0.25 0.4 v coupling capaci tance f = 1 mhz c c 0.4 pf current transfer ratio (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit i c /i f i f = 5 ma, v ce = 5 v vo617a ctr 50 600 % vo617a-1 ctr 40 80 % vo617a-2 ctr 63 125 % vo617a-3 ctr 100 200 % vo617a-4 ctr 160 320 % vo617a-7 ctr 80 160 % vo617a-8 ctr 130 260 % switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition ctr bin symbol min. typ. max. unit non-saturated rise and fall time i f = 5 ma, v cc = 5 v, r l = 75 t r , t f 2s turn-on time i f = 5 ma, v cc = 5 v, r l = 75 t on 3s turn-off time t off 2.3 s cut-off frequency i f = 5 ma, v cc = 5 v, r l = 75 f ctr 100 khz saturated turn-on time i f = 5 ma t on 6s turn-off time i f = 5 ma t off 25 s rise time i f = 5 ma t r 4.6 s fall time i f = 5 ma t f 15 s
vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 4 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 2 - test circuit, non-saturated operation fig. 3 - test circui t, saturated operation fig. 4 - switching times note ? as per din en 60747-5-5, 7.4.3.8.2, this optocoupler is suitab le for safe electrica l insulation only wi thin the safety rat ings. compliance with the safety ratings shall be ensured by means of protective circuits. channel i channel ii 95 10804-3 r g = 50 t p t p = 50 s t = 0.01 + 5 v i f 0 50 r l i f oscilloscope r l = 1 m c l = 20 pf channel i channel ii 95 10843 r g = 50 t p t p = 50 s t = 0.01 + 5 v i c i f 0 50 1 k i f = 10 ma oscilloscope r l c l 20 pf 1 m t p t t 0 0 10 % 90 % 100 % t r t d t on t s t f t off i f i c t p pulse duration t d delay time t r rise time t on (= t d + t r ) turn-on time t s storage time t f fall time t off (= t s + t f ) turn-off time 96 11698 safety and insulation ratings parameter symbol value unit maximum safety ratings output safety power p so 265 mw input safety current i si 130 ma safety temperature t s 150 c comparative tracking index cti 175 insulation rated parameters maximum withstanding isolation voltage v iso 5300 v rms maximum transient isolation voltage v iotm 8000 v peak maximum repetitive pe ak isolation voltage v iorm 890 v peak insulation resistance t amb = 25 c, v dc = 500 v r io 10 12 isolation resistance t amb = 100 c, v dc = 500 v r io 10 11 climatic classification (a ccording to iec 68 part 1) 55/110/21 environment (pollution degree in accordance to din vde 0109) 2 internal and external creepage standard dip-4 7 mm 400 mil dip-4 8 mm clearance standard dip-4 7 mm 400 mil dip-4 8 mm insulation thickness 0.4 mm
vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 5 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 5 - forward voltage vs. forward current fig. 6 - collector current vs. collector emitter voltage fig. 7 - leakage current vs. ambient temperature fig. 8 - collector current vs. collector emitter voltage fig. 9 - normalized current transfer ratio (non-sat.) vs. ambient temperature fig. 10 - normalized current transfer ratio (sat.) vs. ambient temperature 0.1 1 10 100 0.6 0.8 1.0 1.2 1.4 1.6 i f - forward current (ma) v f - forward voltage (v) t amb = 110 c t amb = 75 c t amb = 25 c t amb = 0 c t amb = - 55 c 0 5 10 15 20 25 30 35 40 45 50 55 0 1 2 3 4 5 6 7 8 9 10 i c - collector current (ma) v ce - collector emitter voltage (v) i f = 30 ma i f = 35 ma i f = 1 ma i f = 20 ma i f = 15 ma i f = 10 ma i f = 5 ma i f = 25 ma 0.001 0.01 0.1 1 10 100 1000 10 000 i ce0 - leakage current (na) i f = 0 ma v ce = 40 v v ce = 24 v v ce = 12 v -60 -40 -20 0 20 40 60 80 100 120 t amb - ambient temperature ( c) 0 2 4 6 8 10 12 14 00.10.20.30.4 i c - collector current (ma) v ce - collector emitter voltage (v) i f = 1 ma i f = 10 ma i f = 5 ma i f = 2 ma 0 0.2 0.4 0.6 0.8 1.0 1.2 n ctr - normalized ctr (non- s aturated) -60 -40 -20 0 20 40 60 80 100 120 t amb - ambient temperature ( c) normalized to ctr value: i f = 5 ma, v ce = 5 v, t amb = 25 c i f = 5 ma 0 0.2 0.4 0.6 0.8 1.0 1.2 n ctr - normalized ctr ( s at) i f = 5 ma normalized to ctr value: i f = 5 ma, v ce = 5 v, t amb = 25 c -60 -40 -20 0 20 40 60 80 100 120 t amb - ambient temperature ( c)
vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 6 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 11 - collector emitter voltage vs. ambient temperature fig. 12 - normalized ctr (non-sat.) vs. forward current fig. 13 - normalized ctr (sat.) vs. forward current fig. 14 - f ctr vs. phase angle fig. 15 - f ctr vs. collector current fig. 16 - switching time vs. load resistance 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 v ce s at - collector emitter voltage (v) i c = 1 ma i c = 2 ma i c = 5 ma i f = 10 ma -60 -40 -20 0 20 40 60 80 100 120 t amb - ambient temperature ( c) 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0.1 1 10 100 n ctr - normalized ctr (n s ) i f - forward current (ma) normalized to: i f = 5 a, v ce = 5 v, t amb = 25 c t amb = 0 c t amb = 100 c t amb = 75 c t amb = - 55 c t amb = 25 c 0 0.2 0.4 0.6 0.8 1.0 1.2 0.1 1 10 100 n ctr - normalized ctr ( s at) i f - forward current (ma) v ce = 0.4 v normalized to: i f = 5 ma, v ce = 5 v, t amb = 25 c t amb = 0 c t amb = 75 c t amb = - 55 c t amb = 25 c t amb = 100 c - 160 - 140 - 120 - 100 - 80 - 60 - 40 - 20 0 1 10 100 1000 pha s e angle (deg) f - fre q uency (khz) v ce = 5 v r l = 100 r l = 1000 1 10 100 1000 0.1 1 10 100 f ctr (khz) i c (ma) v cc = 5 v 0.1 1 10 100 1000 0 5 10 15 20 t on , t off s witching time ( s ) r l - load re s i s tance (k ) t off ( s ) t on ( s ) v ce = 5 v, i f = 2 ma
vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 7 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example of VO617A-3X017T) notes ? the vde logo is only marked on option 1 parts. option information is not marked on the part. ? tape and reel suffix (t) is not part of the package marking. 10.16 typ. 7.62 typ. option 6 3.5 0.3 0.1 min. 2.7 min. 8 min. 7.62 typ. 3.5 0.3 0.6 min. 10.16 0.3 option 7 0.35 + 0.25 - 0.3 2.54 1.78 0.76 8 min. 1.52 11.05 r 0.25 0.26 7.62 to 9.98 7.62 0.3 4.58 0.5 2.54 0.25 0.5 0.1 0.85 0.1 2.8 0.5 3.3 0.5 3.5 0.3 0.5 typ. 1.2 0.1 6.5 0.5 pin 1 identifier 12 43 1.2 0.1 0.85 0.1 vo617a-3 v yww 25
vo617a www.vishay.com vishay semiconductors rev. 2.1, 18-oct-13 8 document number: 83430 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 packing information fig. 17 - tape and reel shippi ng medium (1000 units per reel) fig. 18 - tape and packing for option 7 device per tube type units/tube tubes/box units/box dip-4 100 40 4000 regular, special, or bar code label tape slot in core 13" 17999-1 22536-3 ? 1.55 0.05 1.75 0.1 7.5 0.1 16 0.3 0.3 0.05 2 0.1 4 0.1 8 0.1
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
